The Ship Model Forum

The Ship Modelers Source
It is currently Mon Dec 17, 2018 5:25 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 137 posts ]  Go to page Previous  1 ... 3, 4, 5, 6, 7  Next
Author Message
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Dec 15, 2017 12:35 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
I was making a display of various rifle shells, I had removed the gunpowder and primers from about 12 different caliber rifle shells and put the powder in a baby food jar. I needed to clear space on my dads work bench, and as I leaned toward the tool box with a few tools to put away a few slipped from my grasp and fell to the steel work bench top I had placed my left hand out for support as I leaned to the tool box, right next to the open jar of gun powder. As fate would have it the falling tools sparked on the bench top and one fell into the jar. It flash exploded and stripped 3 fingers on my left hand of the flesh to the bone, no tendon damage so after a couple of surgeries and some therapy I had full use of my left hand. I did this when I was 18 a day before I was to graduate from high school, I was in surgery at the exact same time as the rest of my class was in commencement ceremonies.


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Tue Dec 19, 2017 8:17 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
I have a little build station on an end table next to my couch where I sit with my leg up. I constructed all of the half doors and the hinge straps from here. I super glued all the straps to all the doors, then soldered the hinge pins to the the ends of the straps. The heat melted most of the straps off ans I had to re glue almost all of them over. I Used a fresh bottle of super glue and they do stay on better than before. The last photo shows the straps with pins soldered on, after the heat melted the glue.


Attachments:
IMG_5898.JPG
IMG_5898.JPG [ 76.29 KiB | Viewed 642 times ]
IMG_5899.JPG
IMG_5899.JPG [ 63.41 KiB | Viewed 642 times ]
IMG_5900.JPG
IMG_5900.JPG [ 68.06 KiB | Viewed 642 times ]
IMG_5902.JPG
IMG_5902.JPG [ 81.68 KiB | Viewed 642 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Wed Dec 20, 2017 2:06 am 
Offline
User avatar

Joined: Mon Jan 10, 2005 5:30 pm
Posts: 4435
Location: Nr Southampton England
very impressive production line-- and impressive repeatability!!!

Bravo!
JIM B :wave_1:

_________________
....I buy them at three times the speed I build 'em.... will I live long enough to empty my stash...?
http://www.modelshipgallery.com/gallery ... index.html

IPMS UK SIG (special interest group) www.finewaterline.com


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Wed Dec 20, 2017 12:28 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
thank you Jim, It means alot to get these little encouraging comments, Merry Christmas!


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Wed Dec 20, 2017 1:06 pm 
Offline

Joined: Sun Jan 04, 2009 1:31 pm
Posts: 1780
..


Last edited by carr on Fri Dec 14, 2018 2:11 pm, edited 2 times in total.

Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Thu Dec 28, 2017 8:47 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
These plastic side hinge pin pieces should be the last bits to glue onto the gun doors. That is 4 each for the 32 double doors and two each for the 34 sigle doors, you do the math, I would be to intimidated if I actually knew how many it was, lol!


Attachments:
IMG_5903.JPG
IMG_5903.JPG [ 60.59 KiB | Viewed 540 times ]
IMG_5904.JPG
IMG_5904.JPG [ 52.27 KiB | Viewed 540 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Dec 29, 2017 4:37 am 
Offline
User avatar

Joined: Mon Jan 10, 2005 5:30 pm
Posts: 4435
Location: Nr Southampton England
sheesh!

dont do any maths!

:thumbs_up_1: :thumbs_up_1:
JB

_________________
....I buy them at three times the speed I build 'em.... will I live long enough to empty my stash...?
http://www.modelshipgallery.com/gallery ... index.html

IPMS UK SIG (special interest group) www.finewaterline.com


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Sun Jan 07, 2018 11:58 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
Painted doors and hinge ends. now I have to seize the lift ropes to the eye bolts lots of tedious time consumming work, sigh, I LOVE IT!
Also my new toy!


Attachments:
20180107_89.JPG
20180107_89.JPG [ 70.18 KiB | Viewed 483 times ]
20180107_90.JPG
20180107_90.JPG [ 95.24 KiB | Viewed 483 times ]
20180107_91.JPG
20180107_91.JPG [ 81.25 KiB | Viewed 483 times ]
IMG_5911.JPG
IMG_5911.JPG [ 32.31 KiB | Viewed 483 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Wed Jan 31, 2018 4:29 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
Now that my ankle is better and I am out of my cast, my "winter" outdoor chores need to be addressed. So, my ship modeling has slowed, but not stopped. Before I put the gun port doors on, some of the ports have a rain gutter if you will, above them. I am trying to bend polystyrene into a circle and some how heat it enough that it retains that diameter without melting the plastic. Tried a hair dryer with some success but it seems to need justa little more heat, perhaps running a soldering iron around the outside edge? What do you guys think?


Attachments:
IMG_5913.JPG
IMG_5913.JPG [ 57.41 KiB | Viewed 407 times ]
IMG_5914.JPG
IMG_5914.JPG [ 64.45 KiB | Viewed 407 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Thu Feb 01, 2018 11:26 am 
Offline

Joined: Sun Jan 04, 2009 1:31 pm
Posts: 1780
..


Last edited by carr on Fri Dec 14, 2018 2:10 pm, edited 2 times in total.

Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Thu Feb 22, 2018 9:09 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
The hot water method worked great. Finished Port side gun port doors and rudder. working on Starboard door now. Will be making lower masts and tops in the coming days


Attachments:
IMG_5915.JPG
IMG_5915.JPG [ 53.23 KiB | Viewed 349 times ]
IMG_5916.JPG
IMG_5916.JPG [ 50.02 KiB | Viewed 349 times ]
IMG_5917.JPG
IMG_5917.JPG [ 50.65 KiB | Viewed 349 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Feb 23, 2018 10:37 am 
Offline

Joined: Sun Jan 04, 2009 1:31 pm
Posts: 1780
..


Last edited by carr on Fri Dec 14, 2018 2:10 pm, edited 2 times in total.

Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Feb 23, 2018 11:57 am 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
Yes it is white, The British also changed to white Under Nelson to white. I have read the red was to mask the blood splattered on the walls in battle. Nelson said something like the not seeing the blood diminished the sacrifice the sailors gave in battle


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Feb 23, 2018 1:58 pm 
Offline
User avatar

Joined: Mon Jan 10, 2005 5:30 pm
Posts: 4435
Location: Nr Southampton England
great chequerboard effect- !

--- a lot of work there ....

Bravo!
Jim Baumann :wave_1:

_________________
....I buy them at three times the speed I build 'em.... will I live long enough to empty my stash...?
http://www.modelshipgallery.com/gallery ... index.html

IPMS UK SIG (special interest group) www.finewaterline.com


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Fri Feb 23, 2018 4:38 pm 
Offline

Joined: Sun Sep 26, 2010 1:33 pm
Posts: 305
Now that is ship / model building. :thumbs_up_1:

Keith


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Sat Feb 24, 2018 3:09 am 
Offline
User avatar

Joined: Wed Sep 28, 2011 12:04 pm
Posts: 854
Location: Paris
Nice and persistent work :thumbs_up_1:

BTW, as a controllable heat-source I use a hot-air electrical 'reflow' soldering-station. The temperature can be preset from around 100°C to 420°C, which avoids melting or burning materials. They are cheap (around 25€ on the bay) and I am using it a lot for all sorts of heating jobs.

_________________
wefalck

-----------------------------------------------------------------------------------------------------------------------

Image Image Image Image


Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Thu Mar 01, 2018 9:39 pm 
Offline

Joined: Sun Jan 04, 2009 1:31 pm
Posts: 1780
..


Last edited by carr on Fri Dec 14, 2018 2:07 pm, edited 1 time in total.

Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Tue Mar 13, 2018 10:20 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
I have been making progress on the masts and to some degree the Tops.


Attachments:
IMG_5940.JPG
IMG_5940.JPG [ 84.67 KiB | Viewed 208 times ]
IMG_5941.JPG
IMG_5941.JPG [ 73.07 KiB | Viewed 208 times ]
IMG_5942.JPG
IMG_5942.JPG [ 73.29 KiB | Viewed 208 times ]
IMG_5943.JPG
IMG_5943.JPG [ 73.39 KiB | Viewed 208 times ]
IMG_5944.JPG
IMG_5944.JPG [ 63.56 KiB | Viewed 208 times ]
IMG_5946.JPG
IMG_5946.JPG [ 75.76 KiB | Viewed 208 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Tue Mar 13, 2018 10:26 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
was not quite done yet the fore and main top masts are just getting roughed in. The fore top mast tapering in the lathe went like I had never taken a break from doing the Pennsylvania! I surprised it went so that it went so well the first try!


Attachments:
IMG_5947.JPG
IMG_5947.JPG [ 85.68 KiB | Viewed 207 times ]
Report this post
Top
 Profile  
Reply with quote  
 Post subject: Re: Uss Columbus 1819
PostPosted: Tue Mar 13, 2018 10:28 pm 
Offline

Joined: Thu Nov 12, 2009 9:53 pm
Posts: 234
And,no,the masts are not bowed, that is just an effect the camera angle gave them, just in case anyone noticed and had questions.


Report this post
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 137 posts ]  Go to page Previous  1 ... 3, 4, 5, 6, 7  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot], Martocticvs, PetrOs and 11 guests


You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group