The Ship Model Forum

The Ship Modelers Source
It is currently Tue May 21, 2019 1:37 am

All times are UTC - 6 hours [ DST ]

Post new topic Reply to topic  [ 6 posts ] 
Author Message
PostPosted: Sat Nov 08, 2014 7:54 am 

Joined: Mon Apr 28, 2014 9:48 am
Posts: 90
Location: Cuxhaven, Germany
Hello everybody,

although I already finished my "Snowberry" about six months ago now, I'd like to give you a short overview of the building process which took me around one year.
I tried to correct the most evident inaccurcies of this kit.

Adjustment of the hull parts. I had to reorder the two forward halves as they were badly torn. Revell delivered them free of charge - good service!
The portholes are altogether in the wrong position, so I decided to fill out most of them and drill new ones in the correct places (see fotos below).


First "in water survey". Everything watertight. Although it wasn't my intention to fit RC, I prepared everything for a later refit.
You can see the porthole adjustments.


One major nuisance of the kit ist that mighty stem. Something that has to be corrected.


The hull is painted in the typical "Western approaches scheme". I did a lot of research to meet the original colours but in the end I'm not completely satisfied as the green seems to be a bit too loud.


I made a lot of changes to the arrangement of Skylights, vents and lockers on top of the E/R-casing. This was my first attempt...


then I decided to discard the complete 2pdr-platform including foundation and the E/R-Skylight and build them from scratch:


Also I mad a lot of adjustments to the quarterdeck: New foundation for DC-throwers, new DCs, spare anchor ...
Furthermore I fitted new railings made of brass stanchions and wire.


New armour plates on the forecastle and nearly completely rebuilt navigation bridge arrangement.


The radar lantern that is included in the kit looks somewhat like an airport control tower.
I made a new one of styrene:


Detail of forecastle, aft section. The galley hut had to be extended on the port side according to the original configuration:


The anchor winch which is included is complete junk. Made a new one of styrene sheet.
On this shot the slimmed down stem can well be seen.


Detail of Nav.bridge deck and galley hut. The prefabricated wooden decks didn't fit after all my changes, so I just painted the bridge deck grey.
The inclination of the main mast was wrong and I reduced it after this foto was shot.
Scratchbuild: Flag lockers and water tank on top of galley, searchlight platforms, Sliding door at asdic hut and so on...


Some impressions of the complete model:



The bilge keels are far too long but I became aware of this detail too late so I leaved them as they are.
Also the lines of the hull are not very accurate and the quarterdeck is a little too slim but those matters can't be corrected with a reasonable effort.


Hope you enjoyed my little report.
Best regards Stefan

Last edited by CaptHaddock on Sun Nov 09, 2014 2:16 am, edited 2 times in total.

Report this post
Reply with quote  
PostPosted: Sat Nov 08, 2014 7:50 pm 
User avatar

Joined: Tue Jan 11, 2005 1:40 pm
Posts: 6552
Location: In the hills of North Jersey
That is a great looking build. Very crisp and clean.


"Tomorrow is the most important thing in life. Comes into us at midnight very clean. It's perfect when it arrives and it puts itself in our hands. It hopes we've learned something from yesterday." John Wayne

Ship Model Gallery

Report this post
Reply with quote  
PostPosted: Sun Nov 09, 2014 7:33 am 
User avatar

Joined: Sun May 20, 2012 6:01 am
Posts: 379
Location: St. Catharines Ontario Canada
She looks great,Stefan.


K494 HMCS Arnprior
Royal Canadian Navy

Report this post
Reply with quote  
PostPosted: Sun May 28, 2017 2:04 pm 

Joined: Sun Feb 08, 2009 3:18 pm
Posts: 564

Report this post
Reply with quote  
PostPosted: Thu Jun 01, 2017 3:45 am 
User avatar

Joined: Sat Dec 20, 2014 6:22 am
Posts: 47
Great build, Stefan!

Currently on the workbench: Tamiya USS Enterprise; Airfix 1/1200 Ark Royal

Report this post
Reply with quote  
PostPosted: Fri Jun 16, 2017 7:46 pm 
User avatar

Joined: Mon Sep 11, 2006 9:33 pm
Posts: 187
Location: St. Catharines, Ontario Canada

Love the corvette. Gives me inspiration to get back to finishing mine.

James W.

Dry docked:
1/72 HMCS Assiniboine DDE 234-1960
1/72 HMCS Ottawa DDE 229-1960
1/72 HMCS St. Catharines-River Class Frigate-1944
On the slipway:
1/72 HMCS Camrose-Flower Class Corvette-1943
1/72 HMCS Trillium-Flower Class Corvette-1942

Report this post
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 2 guests

You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group