1/350 Warehouse & Dock 16" or 32" Option

NukeMM · Post by **NukeMM** » Sun Sep 21, 2014 9:48 am

NEW 1/350 Warehouse and Dock Sets now available for orders at BACK-AFT Models.

http://shop.back-aft.com/1-350-Dockyard ... es_c10.htm

I need one of these warehouse docks for the diorama that I am planning for my USS Barnegat class AVPs.

This kit depicts the Pier 2 warehouse dock at Norfolk Naval Base. It was built during World War II and still existed as late as the mid 1990's. I'm not sure if it still stands, today. My diorama will be dated about 1953.

I've designed this 1/350 model warehouse in resin and below is the test-fit of the first casting of parts.

The warehouse is designed to be built to any desired length ranging from 10" to 34" or more. For my diorama I'll only need about 15".

I plan to create the instructions for the warehouse's assembly while building the warehouse intended for my diorama. The kits will be available some time after that.

davidwaples · Post by **davidwaples** » Sun Sep 21, 2014 10:39 am

Very nice Carl. You're working on some very interesting projects.
Dave

Post by **Cadman** » Mon Sep 22, 2014 2:06 pm

Does it come with an interior kit with lighting?????

Impressive work.

NukeMM · Post by **NukeMM** » Thu Oct 02, 2014 5:21 pm

Assembling the 1/350 Warehouse.........

Step 1: Sanding the thin resin film from the back side of the walls to open up the windows. This must be done to the window sections and the overhead doors, as well.

Step 2: I recommend painting the wall and window sections and the doors before continuing with Step 3.

Step 3: Filling the windows with Micro Krystal Klear.
This requires placing clear packing tape on the back side of the wall and then filling the window panes with Krystal Klear. It will take at least two applications of the liquid. The same methods were taken with the window sections and the overhead doors.

NukeMM · Post by **NukeMM** » Thu Oct 02, 2014 5:27 pm

Step 4: Attach the overhead doors to the walls. The door pieces can be trimmed to portray open or half-open doorways.

Step 5: Attach wall sections together to extend the length of the warehouse. The doors act as tabs to join the wall sections together. Special tabs are included with open doorways in case the doorway at the walls' attachment points are desired to be open doorways. The seams at the joint of the wall sections will be covered with water downspouts made from .020" styrene rod.

NukeMM · Post by **NukeMM** » Thu Oct 02, 2014 5:31 pm

Step 6: Attach the end wall's door to the end wall.

Step 7: Attaching the side walls to the end wall. Right angled tabs are provided to square up the corners of the end wall and side wall joints.

NukeMM · Post by **NukeMM** » Thu Oct 02, 2014 5:38 pm

Step 8: Attaching the support walls to the side walls. These are to spaced so as not to interfere with roof sections joints that are attached to each other with tabs similar to the lengthened side wall sections.

Step 9: Attach the window sections together to match the desired length of the warehouse. These are assembled similarly to the method of attaching the wall sections together with the use of special tabs. The window sections are then attached to the end wall and the support walls. These seams will be covered by water downspouts, as well.

NukeMM · Post by **NukeMM** » Thu Oct 02, 2014 5:43 pm

Step 10: The upper roof and lower roof sections are lengthened to match the desired length of the warehouse with use of tabs to connect their ends together.

NukeMM · Post by **NukeMM** » Sat Oct 04, 2014 5:23 pm

Step 11: Attaching the lower roof sections.......

NukeMM · Post by **NukeMM** » Sat Oct 04, 2014 5:45 pm

Step 12: Cover the wall and window seams with water downspouts made from .020" styrene rod ....

NukeMM · Post by **NukeMM** » Tue Oct 07, 2014 2:31 pm

Step 13: Attaching the Upper Roof Sections and the Ridgeline.

The warehouse was glued to the completed dock from within before attaching the Upper Roof Sections.

NukeMM · Post by **NukeMM** » Thu Oct 09, 2014 12:46 pm

NEW 1/350 Warehouse and Dock Sets now available for orders at BACK-AFT Models.

http://shop.back-aft.com/1-350-Dockyard ... es_c10.htm

NukeMM · Post by **NukeMM** » Fri Nov 14, 2014 10:03 am

New, reduced pricing on the 1/350 Warehouse and Dock kits.

And Single Bollards (set of 16) included with Dock sections.

http://shop.back-aft.com/1-350-Dockyard ... es_c10.htm

CWO/MRC · Post by **CWO/MRC** » Fri Nov 14, 2014 11:53 am

Too Cool !!!

Pat

rotley · Post by **rotley** » Wed Oct 11, 2017 2:57 pm

Are Back-Aft Models still in business?

Guest · Post by **Guest** » Tue May 21, 2019 7:36 pm

rotley wrote:Are Back-Aft Models still in business?

Something I've been trying to find out too. I heard there was a conversion kit for USS Half Moon, but cannot find, anywhere.

NukeMM · Post by **NukeMM** » Wed Oct 13, 2021 12:07 am

Does anyone know who "Guest" is / was?

I'd like to try and help with the Half Moon parts.

NukeMM · Post by **NukeMM** » Wed Oct 13, 2021 12:15 am

I assembled a whole warehouse, this weekend. I had never done that before, just a short version.

I think it's pretty cool. I just use this one for display / prototype purposes. I found a few flaws in my sequence of instructions and sequence of upper window assembly. It was worth the effort.

NukeMM · Post by **NukeMM** » Wed Oct 13, 2021 8:20 pm

I betcha my Dock is bigger than your Dock.

NukeMM · Post by **NukeMM** » Mon Nov 01, 2021 11:45 am

NEW SHORTER WAREHOUSE OPTION - 16 inches long instead of 32.

A 16 inch-long warehouse with the option of a 21 inch-long dock is now available on my eBay store.

Ebay Listing:
https://www.ebay.com/itm/334203065716?h ... Sw~JhhgBN8

The Ship Model Forum