The Ship Model Forum

The Ship Modelers Source
It is currently Thu Mar 28, 2024 4:01 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 468 posts ]  Go to page Previous  1 ... 8, 9, 10, 11, 12, 13, 14 ... 24  Next
Author Message
PostPosted: Wed May 21, 2014 3:25 pm 
Offline
User avatar

Joined: Sun Mar 07, 2010 12:01 am
Posts: 1643
Location: Corvallis, Oregon, USA
I discussed boat colors in this thread:

viewtopic.php?f=27&t=70810

Admiral's barges had black hulls and lots of fancy trim. Other boats had gray hulls, with less chrome and trim for lower ranking commands. As you can see in the other thread there were differences between underside hull colors, waterline stripes, etc.

The OK City's Captain's barge had a dual red and white waterline up until sometime in late 1970 or early 1971 when a single red stripe was used.

Phil

_________________
A collision at sea will ruin your entire day. Aristotle


Top
 Profile  
Reply with quote  
PostPosted: Tue Jun 17, 2014 7:14 pm 
Offline
User avatar

Joined: Wed May 26, 2010 1:57 pm
Posts: 1296
Location: Schodack Landing, NY
I'll be touring the Buffalo Naval Park and the USS Little Rock later this week (June 19) - if anyone would like some particular pictures, let me know.


Top
 Profile  
Reply with quote  
PostPosted: Tue Jun 17, 2014 8:15 pm 
Offline
User avatar

Joined: Wed Nov 27, 2013 7:06 am
Posts: 3154
Location: Vancouver, Canada
D-Boy wrote:
I'll be touring the Buffalo Naval Park and the USS Little Rock later this week (June 19) - if anyone would like some particular pictures, let me know.


Yes please.

Any pictures of the full length of the starboard or port side of the ship would be greatly appreciated.

_________________
"Haijun" means "navy" in Mandarin Chinese.

"You have enemies? Good. It means you stood up for something in your life."- Winston Churchill


Top
 Profile  
Reply with quote  
PostPosted: Wed Jun 18, 2014 6:40 pm 
Offline
User avatar

Joined: Wed May 26, 2010 1:57 pm
Posts: 1296
Location: Schodack Landing, NY
Haijun watcher wrote:

D-Boy: I'll be touring the Buffalo Naval Park and the USS Little Rock later this week (June 19) - if anyone would like some particular pictures, let me know.

Yes please.

Any pictures of the full length of the starboard or port side of the ship would be greatly appreciated.


She's got an SSK and a DD moored inside of her. Are you looking for deck down (hull) or deck up (superstructure) photos?

Photos will be from her starboard side... I don't have telephoto lenses to take anything detailed of her port side.

DBoy


Top
 Profile  
Reply with quote  
PostPosted: Wed Jun 18, 2014 7:09 pm 
Offline
User avatar

Joined: Wed Nov 27, 2013 7:06 am
Posts: 3154
Location: Vancouver, Canada
D-Boy wrote:

She's got an SSK and a DD moored inside of her. Are you looking for deck down (hull) or deck up (superstructure) photos?

Photos will be from her starboard side... I don't have telephoto lenses to take anything detailed of her port side.

DBoy


Deck up if possible. I could have visited the ship when I was visited the Niagara region back in 2009, but had other things to tend to back then. Oh well.

_________________
"Haijun" means "navy" in Mandarin Chinese.

"You have enemies? Good. It means you stood up for something in your life."- Winston Churchill


Top
 Profile  
Reply with quote  
PostPosted: Thu Jun 19, 2014 9:01 pm 
Offline
User avatar

Joined: Wed May 26, 2010 1:57 pm
Posts: 1296
Location: Schodack Landing, NY
I'll be touring the Buffalo Naval Park and the USS Little Rock later this week (June 19) - if anyone would like some particular pictures, let me know.

Haijun Watcher:

<<Yes please. Any pictures of the full length of the starboard or port side of the ship would be greatly appreciated.>>

Took over 150 photos of the USS Little Rock today. Will sort and label and post in a "permanent" folder on Photobucket and link back here.

On past business trips to Buffalo, I've never had time to tour the three museum ships moored there, and was glad to get there this time. Little Rock has got to be a huge maintenance responsibility, and she shows some wear and tear in places. But I think you will find the photos useful; they document the ships hull and superstructure exterior to the extent that shipboard angles and access allowed. I'll post a link this weekend.

Frankly, the most intriguing part of access to the ship is the Talos missile handling compartment toward the stern. The machinery for storage and assembly in that space is stunning in complexity, massive in size, and certainly explains why the ship had only room for one launcher.

Here's a link to a film shown on board in the missile hanger: https://www.youtube.com/watch?v=rgFIhomusc8

I'll be posting folders for SSK Croaker and DD Sullivans as well, and will link to the appropriate forums for those vessels as well.

D-Boy


Last edited by D-Boy on Fri Jun 20, 2014 8:11 am, edited 1 time in total.

Top
 Profile  
Reply with quote  
PostPosted: Fri Jun 20, 2014 12:21 am 
Offline
User avatar

Joined: Sun Mar 07, 2010 12:01 am
Posts: 1643
Location: Corvallis, Oregon, USA
It was quite a trip working inside the Talos launching system while all that machinery was moving! It was one of the first shipboard missile handling systems and they still had a lot to learn about how to make things work. There was a lot of maintenance required to keep everything working. The size of the Talos missile (30 feet long, 30 inches diameter) made everything huge.

Here is a description of how it worked:

http://www.okieboat.com/Talos%20launching%20system.html

And if you want more details here are the training manuals:

http://www.okieboat.com/GMM.html

Phil

_________________
A collision at sea will ruin your entire day. Aristotle


Top
 Profile  
Reply with quote  
PostPosted: Fri Jun 20, 2014 8:07 am 
Offline
User avatar

Joined: Wed May 26, 2010 1:57 pm
Posts: 1296
Location: Schodack Landing, NY
DrPR wrote:
It was quite a trip working inside the Talos launching system while all that machinery was moving! It was one of the first shipboard missile handling systems and they still had a lot to learn about how to make things work. There was a lot of maintenance required to keep everything working. The size of the Talos missile (30 feet long, 30 inches diameter) made everything huge.

Here is a description of how it worked:

http://www.okieboat.com/Talos%20launching%20system.html

And if you want more details here are the training manuals:

http://www.okieboat.com/GMM.html

Phil


Phil, the maintenance responsibilities were at the forefront of my thinking in that space. I found your documentation later last night - thanks for such a detailed effort to document the process! And your CAD work is impressive! http://www.okieboat.com/CAD%20superstructure.html


Top
 Profile  
Reply with quote  
PostPosted: Sun Jun 22, 2014 12:22 am 
Offline
User avatar

Joined: Sun Mar 07, 2010 12:01 am
Posts: 1643
Location: Corvallis, Oregon, USA
The launching system worked very reliably, but there were a few quirks. The transfer carts had pneumatic systems - valves and motors. But the air supply on the ship collected a lot of water from condensation. At sea, when the ship was rolling, that water made its way through the system and the motors gave everything a bath of water and oil - a real mess. We had electrically conductive plastic sheets to cover the missiles.

I knew this just couldn't be the way it was designed, so I sent the GM Division Chief PO to look for a solution. After consulting with the ship's Damage Control Officer and looking over air system blueprints he discovered that there was an air drier on the mess decks, below the missile house. Seems it had been forgotten about, and the last time the dryer cartridges had been replaced in the shipyard someone left the valves set to bypass the dryer. After they set the valves correctly we had dry air!

****

The missile stowage magazine and ready service magazine equipments were designed by different companies. The ready service magazine worked perfectly, without too much maintenance, even though it had a huge number of moving parts. The stowage magazine was something else. The hydraulic cranes used a fluid that dissolved the seals. After a while hydraulic fluid leaked out of everything and pooled on the decks. Fortunately, it wasn't flammable, but it was a constant mess.

The missile launcher was made by the same company that made the stowage magazine, and they used the same hydraulic fluid. A standard part of the repair tools for the launcher was an umbrella. When it was running hydraulic fluid dripped from everywhere. On the other hand, nothing rusted!

Phil

_________________
A collision at sea will ruin your entire day. Aristotle


Top
 Profile  
Reply with quote  
PostPosted: Sun Jun 22, 2014 7:20 am 
Offline
User avatar

Joined: Wed May 26, 2010 1:57 pm
Posts: 1296
Location: Schodack Landing, NY
Not yet in any order, here is a link to pictures of the Little Rock from my visit in June 2014.

http://s1122.photobucket.com/user/DrWind/library/USS%20Little%20Rock%20CL92?sort=3&page=1

General order of photos is as follows:

Pier side, bow to stern.

Stern to bow from deck of the USS Sullivans.

Stern, deck level, on board USS Little Rock. From this point I followed the self-guided tour route, climbing two levels to bridge deck and above. Tour concludes on bow.

I'll start labeling these photos, but wanted to provide general access.


Top
 Profile  
Reply with quote  
PostPosted: Mon Aug 11, 2014 12:14 am 
Offline
User avatar

Joined: Tue Apr 13, 2010 9:35 pm
Posts: 50
Please don't pelt me with rotten tomatoes....

I build WW2 ships in the dead 1/600 scale (what can I say, I enjoy the pain it brings).

Options for US warships in 1/600 are few and far between, particularly with cruisers. In fact, the only cruiser I have found in 1/600 is the Lindberg USS Manchester.

There are 2 issues with this kit:
1) It is not very good
2) The Manchester was completed in 1946, so I'd like to 'convert' the kit to the USS Cleveland.

My questions are:
1) What are the physical differences between the Cleveland and Manchester?
2) Does anyone have any experience with this kit? If so, any advice (other than the obvious 'throw it away') on how to make it more accurate?

_________________
After so much backchat it is but right, that Soemba should join in this fight - Soemba Docket


Top
 Profile  
Reply with quote  
PostPosted: Mon Aug 11, 2014 6:32 pm 
Offline
User avatar

Joined: Tue Apr 13, 2010 9:35 pm
Posts: 50
DavidP wrote:
what are yor scratch building skills like? read this link as also applies to manchester.
http://www.quuxuum.org/rajens_list/ship ... l#LindClev

I was hoping you wouldn't say that...

My skills are limited. I can do basic scratch building, like superstructure, decking, funnels, etc. But I'm not so comfortable with building guns (of any size), or hulls.

I can definitely replace the deck, and re-do the superstructure, but I'm hoping the hull is passable? If not, what needs to change?

_________________
After so much backchat it is but right, that Soemba should join in this fight - Soemba Docket


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 27, 2014 1:33 pm 
Offline
User avatar

Joined: Mon May 21, 2007 5:49 pm
Posts: 1586
Location: The beautiful PNW
Hey all,

Was perusing navsource and came across a couple pictures of the USS Amsterdam CL-101 in a very attractive and different camouflage. There are two shots from the bow and from the stern but both from the starboard side only. Couple of questions, what was this scheme called? What colors? And are there any pics of the port side?

Thanks
Matt

_________________
In the yards right now:
USS Utah AG-16
On Hold
1/350 USS Portland CA-33 1942
1/350 Trumpeter Texas with a twist


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 27, 2014 1:57 pm 
Offline
User avatar

Joined: Sun Feb 01, 2009 3:55 pm
Posts: 3125
Location: Hawaii
Well Navsource is currently down so I can't find the photos on there but it seems that Wiki might have one of those ones you're talking about.

Is this it? http://upload.wikimedia.org/wikipedia/commons/8/83/USS_Amsterdam_%28CL-101%29.jpg

Shipcamouflage.com states that she wore Ms 31a/10C of which I can't find any design sheets. Ms 31 called for 5-H,5-O, and Black. In all honesty though that darkest color does NOT look like black based on the darkness of the blast bags and their sharp contrast to the hull. If I had to guess I'd say it was 5-N with either 5-H, and 5-O, or maybe 5-H, and 5-P or 5-L. No idea really unless someone can track down the design sheet. They modified those schemes at times so you can't "always" go by what the core measure called for color wise.

_________________
Drawing Board:
1/700 Whiff USS Leyte and escorts 1984
1/700 Whiff USN Modernized CAs 1984
1/700 Whiff ASW Showdown - FFs vs SSGN 1984

Slipway:
1/700 Whiff USN ASW Hunter Killer Group Dio 1984


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 27, 2014 2:51 pm 
Offline
User avatar

Joined: Mon May 21, 2007 5:49 pm
Posts: 1586
Location: The beautiful PNW
Thanks for the reply Cliffy, Mr. Roger Torgeson came to my aid and provided me a link with a design sheet. That picture you posted seems a hair sharper than the navsource one, so I will be saving that one.

Thanks,
http://usndazzle.com/1Web/DrawingsCL/10C%20CL55.html

_________________
In the yards right now:
USS Utah AG-16
On Hold
1/350 USS Portland CA-33 1942
1/350 Trumpeter Texas with a twist


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 27, 2014 3:36 pm 
Offline
User avatar

Joined: Sun Feb 01, 2009 3:55 pm
Posts: 3125
Location: Hawaii
Awesome!!!! Always loved the schemes with 5-N as the darkest color. They just look cool! Add the wavy demarcations and this scheme is awesome!!!

_________________
Drawing Board:
1/700 Whiff USS Leyte and escorts 1984
1/700 Whiff USN Modernized CAs 1984
1/700 Whiff ASW Showdown - FFs vs SSGN 1984

Slipway:
1/700 Whiff USN ASW Hunter Killer Group Dio 1984


Top
 Profile  
Reply with quote  
PostPosted: Wed Nov 11, 2015 3:56 pm 
Offline

Joined: Thu Sep 17, 2015 8:42 pm
Posts: 165
Does anyone have a rigging diagram for the square bridge Clevelands? Found a build here on MW but I need some diagrams to base the pictures on. Hate to bump an old thread but I need the help.

_________________
Mike, MikeyBugs


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 12, 2015 12:49 am 
Offline
User avatar

Joined: Sun Mar 07, 2010 12:01 am
Posts: 1643
Location: Corvallis, Oregon, USA
The "Booklet of General Plans: for the USS Miami CL-89 shows some rigging. You can find it here:

http://archive.hnsa.org/doc/plans/index.htm

Phil

_________________
A collision at sea will ruin your entire day. Aristotle


Top
 Profile  
Reply with quote  
PostPosted: Thu Nov 12, 2015 1:12 am 
Offline

Joined: Thu Sep 17, 2015 8:42 pm
Posts: 165
Thanks. Not sure how well it'll help with rigging but it'll definitely help with placement of various items like floater net baskets and such.

_________________
Mike, MikeyBugs


Top
 Profile  
Reply with quote  
PostPosted: Thu Feb 04, 2016 11:51 am 
Offline

Joined: Thu Sep 17, 2015 8:42 pm
Posts: 165
Does anyone know of any other deck plans for any Clevelands? I'm already using the HNSA general plans booklet for the USS Miami CL-89 extensively for my build. But more plans would be immensely helpful. Especially for some other ships as well.

_________________
Mike, MikeyBugs


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 468 posts ]  Go to page Previous  1 ... 8, 9, 10, 11, 12, 13, 14 ... 24  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Vlad and 43 guests


You can post new topics in this forum
You can reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group