Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Moderators: BB62vet, MartinJQuinn, JIM BAUMANN, Jon, Dan K
-
Russ2146
- Posts: 2126
- Joined: Tue Nov 03, 2009 9:28 pm
- Location: Egg Harbor Twp, NJ
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Hi,
Like the idea and I'll put a Missouri to Wisconsin attempt on hold as long as necessary.
Have you tried woods besides teak and maple?
It might be interesting to put a sample of each up on your website.
I was thinking of beech and particularly poplar as possibilities. The issue with poplar is the green coloration it can have, but sands to almost a glass like surface which minimzes open grain.
Like the idea and I'll put a Missouri to Wisconsin attempt on hold as long as necessary.
Have you tried woods besides teak and maple?
It might be interesting to put a sample of each up on your website.
I was thinking of beech and particularly poplar as possibilities. The issue with poplar is the green coloration it can have, but sands to almost a glass like surface which minimzes open grain.
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
We looked at a lot of woods, including birch, bamboo, red oak, white oak... The best grain patterns for our purposes were on the maple. Teak looked good as a darker wood, and although the grain was a bit pronounced it is definitely an "authentic" material that has a certain appeal as being "the real stuff."Russ2146 wrote:Hi,
Have you tried woods besides teak and maple?
It might be interesting to put a sample of each up on your website.
I was thinking of beech and particularly poplar as possibilities. The issue with poplar is the green coloration it can have, but sands to almost a glass like surface which minimzes open grain.
Next time we order wood I will take a look at beech and poplar if they are available. And we will have wood samples for sure on the website.
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
- Charlestonguy
- Posts: 1216
- Joined: Wed Apr 02, 2008 6:23 am
- Location: South Carolina USA
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Do you post on ebay under general 1/350 scale or do you use a web store name? I checked for the Borodino deck tonight and never found it.
I hope you will be able to keep the price down for the super detail decks, another big ticket item for my Bismarck will push the wife over the edge.
I hope you will be able to keep the price down for the super detail decks, another big ticket item for my Bismarck will push the wife over the edge.
"Only two sailors, in my experience, never ran aground. One never left
port and the other was an atrocious liar."
-Don Bamford
port and the other was an atrocious liar."
-Don Bamford
-
Guest
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Holly has the finest grain I know of and even that would be too coarse for me but I am sometimes a woodworker so I get picky about wood. You can also get laser printers that will do 1200dpi reasonably cheap or up to 2400dpi for stupid amounts of money, it just depends on the software you're printing from to drive those resolutions. Discernible grain, grossly overscale planks and the mixed media problem presented by laminating very thin wood to plastic (with all the problems wood has expanding and contracting due to humidity) takes it out of the running for me. Not ragging you, just giving my honest opinion.
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
If you enter "Borodino Wood Deck" in the eBay search that should take you right there. I list under the username jdigiant. We will sell the super-detail decks for the same price as the out-of-the-box decks for each ship. They don't cost us any more or less to produce, and are actually a simpler engineering process as we will mostly just be removing cutouts from the normal OOB decks!Charlestonguy wrote:Do you post on ebay under general 1/350 scale or do you use a web store name? I checked for the Borodino deck tonight and never found it.
I hope you will be able to keep the price down for the super detail decks, another big ticket item for my Bismarck will push the wife over the edge.
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
- navydavesof
- Posts: 3127
- Joined: Thu Mar 05, 2009 10:38 pm
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Oh, my. Someone has finally come to the rescue. Thank you so much. You are about to corner the market!johnd13 wrote:
Next candidates (This is what we have planned, but these are definitely subject to change due to demand):
A refit of the Tamiya Missouri/New Jersey to fit the Revell 1/350 kits of those two ships
Proper Preparation Prevents Poor Performance
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
No problem - I appreciate the feedback. I checked with my mill, and they don't offer holly. I can get beech, poplar and yellow poplar as Russ suggested. I am also looking at basswood, red oak, and black gum as possibilities. Next time I place an order I will get some sheets in those species and try printing on them to see what kind of results I get.Guest wrote:Holly has the finest grain I know of and even that would be too coarse for me but I am sometimes a woodworker so I get picky about wood. You can also get laser printers that will do 1200dpi reasonably cheap or up to 2400dpi for stupid amounts of money, it just depends on the software you're printing from to drive those resolutions. Discernible grain, grossly overscale planks and the mixed media problem presented by laminating very thin wood to plastic (with all the problems wood has expanding and contracting due to humidity) takes it out of the running for me. Not ragging you, just giving my honest opinion.
As for resolution, my work in computer graphics tells me that the human eye has difficulty distinguishing anything finer than 1/1000 of an inch. The deck lines that I am printing now are pretty fine; I may try going finer, but at some point you start fighting with what the eye actually perceives, and how the brain interprets those visual signals.
For example, during a stint as a photography student I learned a valuable lesson. I was mathematically centering my prints in the mats that I was cutting. They were pefectly centered. My instructor said, "you need to make them off center with a little extra space at the bottom to make them look centered." It didn't make any sense at all, but by golly it sure turned out to be true. And I am applying that lesson here - particularly when faced with some incredibly small scales for plank lines, and incredibly large grain on the wood. I don't need it to be "mathematically correct" - I just need it to "look right."
I don't know what alternatives we as hobbyists would have. Would a deck pattern printed in color on a sheet of paper or plastic with 1200 dpi resolution be preferable? I could probably take some photos of an existing teak deck on a ship somewhere and then photoshop that into a very fine detail and print out sheets of that. But I fear that it would resolve down to just a tan mushy blur to the human eye, and who would want to put that on their models - even if it was totally accurate and mathemetically correct? it would be easier to just paint the deck a uniform tan.
Some eyes will look at a model deck and say, "the planks are overscale" or "the grain is to large." Others will say, "the deck looks incredibly real - is that real wood?" I certainly realize that you can't please everybody. We all know that we look at photos of models posted here sometimes and think, "Ew... That's nasty. I can't believe that guy is proud of that mess." But if he is, then it really doesn't matter what we think, does it?
I have read the threads on how to simulate wood, and you can get some pretty nice results with that - but the "planks" there are certainly overscale. And you could argue that, in theory, you should put down a dark layer to simulate the lines between the boards, then paint individual planks on that leaving a gap between them. At least in theory. But that would be a nightmare to do, and you'd still have overscale planks at 1/350. Or I suppose you could do it under a microscope to get it right, and then people viewing your model would have to do so under a microscope to truly appreciate your dedication to detail.
I don't know... Until the evil Doctor Nefario perfects his "Shrink Ray" technology, I think we modelers are going to have to make compromises of some sort. For me, I know what my decks looked lke when I painted them a uniform tan, and for me using a sheet of real wood is infinitely better. Others may choose to adopt another approach. And some may choose to wait for Doctor Nefario... And that's what makes this hobby great! Every modeler can choose the methods that they prefer to bring their ships' details to life, and select the techniques that best represent their vision of what their models should look like to please their own eye. if I can produce a product to help some people achieve a result that they seek, then I will be thrilled.
And if I can be compensated just enough to make the investment of time, equipment and materials worthwhile, then that wouldn't be a bad thing either!
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
-
redsoldiergreen
- Posts: 20
- Joined: Mon Oct 04, 2010 2:29 pm
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Martin -redsoldiergreen wrote:Hi John . Im enjoying this thread . All the best to you in this venture . Im just back into modelling and have the Varyag to come from santa
.Hes also bringing me the etched brass ,barrels and masts to go with it ,so im hanging on for your decks .Do you think they will be availiable in the UK? Also will these things be limited or one offs etc?Good luck .
Martin
Sounds like you have a very Merry Christmas indeed in store for you. Tell Santa that if he stops by eBay and does a search for "Varyag Wood Deck" that he can have one drop shipped to any address in the UK. I already priced out a Borodino deck to ship to Aberdeen Grampian (?) in the UK and International First Class Postage adds $3.96(US) to the posted price.
The Varyag and Borodino are now "in production." I am still informal on my packaging, but the goods themselves are the real deal. I have several in stock right now, and can make as many more as the building community demands.
Wishing you the happiest of new years!
-- John D. --
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
-
redsoldiergreen
- Posts: 20
- Joined: Mon Oct 04, 2010 2:29 pm
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
thanks John . Expect an order soon
- Charlestonguy
- Posts: 1216
- Joined: Wed Apr 02, 2008 6:23 am
- Location: South Carolina USA
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
John
Have you considered offering square generic sheets with the planks printed? Could be handy for cutting in around opening and deck edges; just slice them up as needed.
Just a thought....

Have you considered offering square generic sheets with the planks printed? Could be handy for cutting in around opening and deck edges; just slice them up as needed.
Just a thought....
"Only two sailors, in my experience, never ran aground. One never left
port and the other was an atrocious liar."
-Don Bamford
port and the other was an atrocious liar."
-Don Bamford
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Funny you should ask... This is a quote from a Private Message that I sent out last night:Charlestonguy wrote:John
Have you considered offering square generic sheets with the planks printed? Could be handy for cutting in around opening and deck edges; just slice them up as needed.
Just a thought....
Of course, a blank sheet with planking on it is really just Option 2 without the template starter. So, let me ask the community at large - do either (or both!) of those sound like something that you would be interested in?Let me bounce two concepts off of you...
1. First option, we print a full set of planking patterns on the top surface of the wood. On the UNDERSIDE we print the cut pattern - but in REVERSE so that if you cut through from underneath you can match the kit cutouts that we normally sell, or you can leave them uncut entirely so that you have a full deck in place there with perfect virgin planking on top. This would be useful in situations where you wanted to fix kit errors, or perhaps make an earlier version of the ship such as before later equipment was added during refits...
2. Second option, we provide just a plain sheet of deck plank printing on a sheet of wood, along with a cardstock template laser cut with the lines that would normally be cut in the wood. This would allow you to use the factory-fit cardstock as templates to test fit and make adjustments. Basically, you would have cardstock to manipulate, hack, extend or otherwise junk up until you get it to fit right, then be able to use those messy shapes as templates to transfer your final pattern onto the pristine planked wood.
We could do Option 1 with a little bit of work (and we'd not be able to do that for ships with intricate, non-standard planking patterns printed onto the decks). Option two would be incredibly easy to do right now... Just send the printed wood uncut, and do the cutting on a companion piece of cardstock, and then ship both.
Would either option be, "WOW! That would be GREAT and I WOULD BUY THAT! That's EXACTLY what I would want!" (if not specifically for the Borodino, perhaps for some other ship that you are building or would plan to build?)
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
- Charlestonguy
- Posts: 1216
- Joined: Wed Apr 02, 2008 6:23 am
- Location: South Carolina USA
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Well my vote would be for option 2. I would like to have the plain sheet so I could use it on any ship. No need for template.
I just placed my order for Borodino deck,
waiting now for the Bismarck 
I just placed my order for Borodino deck,
"Only two sailors, in my experience, never ran aground. One never left
port and the other was an atrocious liar."
-Don Bamford
port and the other was an atrocious liar."
-Don Bamford
-
redsoldiergreen
- Posts: 20
- Joined: Mon Oct 04, 2010 2:29 pm
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
I like option 2 . or just scribed wood ,with the option of a template if you wanted one . 
-
JCRAY
- Posts: 633
- Joined: Sun Feb 08, 2009 3:18 pm
- Location: Palm Beach, Fla
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
MK 1 sells full printed deck sheets in 350 & 250sc.
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
Wow - they do! I just found some on eBay out of Korea and ordered one to take a look. Price with shipping: $42! Wow - more than my engineered and cut product. Interesting. The shipment looks really slow, though - anticipated delivery date of January 6th.JCRAY wrote:MK 1 sells full printed deck sheets in 350 & 250sc.
I don't know how big the sheet is, or the quality of the deck lines. But I'll take a look and post some photos here when it arrives along side some of my printed stock so that we can all compare. For the price they are charging, I know I can come in a lot lower than that - and I suspect I can deliver a higher quality product on a variety of woods, too.
-- John D. --
Last edited by johnd13 on Sun Dec 05, 2010 3:46 am, edited 1 time in total.
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Wood Decks - Maple vs Teak
I wanted to take a moment here and show the difference between Maple and Teak as a material for the decks. I've taken some pictures, but lighting is always tricky... So I have the following variants, all of the same two decks.
I have found that the maple is more typical of other available deck products. The teak is much darker and richer in grain. I would think that a diorama of a ship with a wet deck would definitely want to go with teak.
For me, I am building the Borodino with teak, since the ship was painted black. The deck contrasts nicely with the black, and adds some nice color. Soon I will be building the Varyag, painted white, and I will want the deck to provide some color, so I will go with teak there, too. But I really like the look of the teak. It is dark, but I prefer that.
The maple has much more subtle grain. It would have a similar tonality to a Haze Grey or other light type color. It provides a lower-contrast balance to a typical grey ship - and that can be nice too. Some people definitely prefer the lighter look.
I think it really comes down to personal preference, so that's why we offer both.
For me, I am building the Borodino with teak, since the ship was painted black. The deck contrasts nicely with the black, and adds some nice color. Soon I will be building the Varyag, painted white, and I will want the deck to provide some color, so I will go with teak there, too. But I really like the look of the teak. It is dark, but I prefer that.
The maple has much more subtle grain. It would have a similar tonality to a Haze Grey or other light type color. It provides a lower-contrast balance to a typical grey ship - and that can be nice too. Some people definitely prefer the lighter look.
I think it really comes down to personal preference, so that's why we offer both.
Last edited by johnd13 on Sun Dec 05, 2010 3:49 am, edited 1 time in total.
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
Wood Deck Close-ups, and Questions on Plank Lines
Here are two close-up photos of the Borodino, this time with the maple deck placed. Note again that this deck is NOT GLUED DOWN, and it's very thin and hovering above the plastic kit deck. So don't look at the gaps that are shown here - this is just to look at the color of the deck against the ship. (The camera actually darkened the image versus the photo of the deeper teak color, so use the comparison of the two deck side-by-side to get a better feel for the contrasting colors!) Also, the translucent maple is darkened by painting the plastic deck the same color near-black as the hull. The net effect is a darkening of the maple wood above.
The plank cuts at the ends were very problematic for us, and we're still experimenting with those, so I'd like to hear some feedback on that.
When we first started experimenting, we attempted to have to the laser operate at two different power levels - first at high-power to burn through the wood, then at low power to just scorch in the deck line patterns. But the way the cutters work is that when they are doing long, straight lines, they go fast. When they do short, intricate lines, they go slow. And as a result, the cut marks at the ends of the planks were thicker and darker, since the laser was moving slower... That made the end cuts more pronounced than the lines between the planks side-to-side. (You can see this problem on the Academy, MK1 and Hasegawa decks illustrated on Page 3 of this thread.)
This was the main reason that we went a different route, and concentrated on printing the plank lines exactly how we wanted them, and then just cut the pattern out of that. A device that does good cutting is not necessarily the best for doing marking, although it's a lot easier to just do it all on one machine. But for me, it was more important to get it right for the modeler than to make it easy for the manufacturer - mainly because I am a modeler, too!
These light cuts at the end are very subtle.
Let me show you another experiment. Here is a photo of two different weights of lines side-by-side. If you look closely at the photo, you can see that the top deck has heavy deck lines, with very definite end cuts and the bottom is much lighter. (For reference, the diameter of the circle cut is only 1cm, or 3/8 of an inch.) Since the plank size is overscale anyway (as it has to be on a 1/350 scale model) my feeling was that I wanted the smallest, thinnest, most subtle plank lines possible. Once again, I feel that might be "just me" - so I'd value to hear various opinions on what you would like to see in terms of the weight of the plank lines.
Thanks, all!
-- John D. --
When we first started experimenting, we attempted to have to the laser operate at two different power levels - first at high-power to burn through the wood, then at low power to just scorch in the deck line patterns. But the way the cutters work is that when they are doing long, straight lines, they go fast. When they do short, intricate lines, they go slow. And as a result, the cut marks at the ends of the planks were thicker and darker, since the laser was moving slower... That made the end cuts more pronounced than the lines between the planks side-to-side. (You can see this problem on the Academy, MK1 and Hasegawa decks illustrated on Page 3 of this thread.)
This was the main reason that we went a different route, and concentrated on printing the plank lines exactly how we wanted them, and then just cut the pattern out of that. A device that does good cutting is not necessarily the best for doing marking, although it's a lot easier to just do it all on one machine. But for me, it was more important to get it right for the modeler than to make it easy for the manufacturer - mainly because I am a modeler, too!
These light cuts at the end are very subtle.
Let me show you another experiment. Here is a photo of two different weights of lines side-by-side. If you look closely at the photo, you can see that the top deck has heavy deck lines, with very definite end cuts and the bottom is much lighter. (For reference, the diameter of the circle cut is only 1cm, or 3/8 of an inch.) Since the plank size is overscale anyway (as it has to be on a 1/350 scale model) my feeling was that I wanted the smallest, thinnest, most subtle plank lines possible. Once again, I feel that might be "just me" - so I'd value to hear various opinions on what you would like to see in terms of the weight of the plank lines.
Thanks, all!
-- John D. --
Last edited by johnd13 on Sun Dec 05, 2010 4:03 am, edited 4 times in total.
scaledecks.com - Proud Sponsor of the ModelWarships.com community!
-
Russ2146
- Posts: 2126
- Joined: Tue Nov 03, 2009 9:28 pm
- Location: Egg Harbor Twp, NJ
Re: Testing New Wood Deck Technique on 1/350 Zvezda Borodino
IMO, the natural grain is more of a distraction to the eye with the finer lines. Being bolder, the diagonal graincatches the eye and I have to refocus to catch the fine lines. Whether this holds true for all species of wood, remains to be seen.
Russ
Russ
-
johnd13
- Scale Decks

- Posts: 163
- Joined: Sun Nov 28, 2010 1:33 am
- Location: Southern California
- Contact:
A Good Brass Porthole Ring Technique
I haven't taken the time to count all of the friggin' portholes on the Borodino, but there are a LOT of them. The WEM brass includes porthole rings for each of them. And actually, that's a really great thing. The Borodino was painted black, and kept the porthole rings polished brass. Reports at the time stated that this presented "a smart appearance." And I agree - so I want to mount all of those brass porthole rings.
The kit has porthole rings molded in already. But the thought of painting them all brass is a nightmare. So I drilled them all out, and scraped off all the molded-in rings to give me a flat hull to glue the rings to.
What the WEM rings do is they allow you to put a perfectly shaped brass ring around your portholes. And, you can paint right up to them, around them, and even over them. THEN, when it's all dry, you can take an X-Acto blade or sandpaper and carefully scrape any paint off of the face of the ring, exposing the shiny brass underneath.
Presto! Black hull, polished brass porthole ring - perfectly round, perfectly edged, perfectly uniform thickness. Perfect.
My son and I spent some time perfecting a technique to mount all of these buggers, and we came up with a pretty good four-hands approach that I thought I would share here.
First, we cut the rings from the brass sheet and placed them on a brass rod. Tape on the rod keeps them from falling off the back, and also provides a pretty workable grip. By placing the rings on the rod as a block, you also have a large consistent surface that you can file as a group to remove the burrs from where you cut the rings from the sheet to help ensure good roundness. Any burr will stick up and thus be easy to identify and file down.
Next, a single ring is isolated and slid down the rod with a blade or fine tweezers: With the ring ready to go and in my son's able hands, I would place a drop of CA glue over the drilled hole, forming a ring around the outside. My son would insert the rod in the hole, slide the ring the rest of the way down into the glue, and press it into place with some sharp tweezers (the ones with the bent head proved to be highly effective here!) He would then extract the rod from the hole, holding the ring in place with the tweezers. Most of the time, but not all of the time, the ring will stay where it is supposed to stay when the tweezers are withdrawn. If so, then I would squeeze the ring firmly into place, clamping it between my thumb and forefinger with a paper towel to soak up any excess glue. I would then prep the next hole by scraping as appropriate, and preparing to add my drop of glue.
Meanwhile, my son would carefully sand any lingering glue from the tip of the rod, and also the tips of the tweezers if needed. We sanded the rod after just about every porthole, and sanded the tweezers after every few. You'd develop your own rhythm for that - once the rings start sticking to the rod, or coming away with the tweezers, it's time for tool cleanup! In terms of progress on the Borodino, we have over half of the portholes in place now after a few hours of four-hands work. I hope to get the rest of them in place tonight, so then I can paint and scrape the brass. Once those are in place, then the the hull prep is just about wrapped, and I can FINALLY glue down my aft deck, and I'll be able to post some pictures of that in place.
As for the fore deck, it's really tricky. It attaches to the bow directly, but also sandwiches between the huill sides in a slot in the middle of those pieces (this is all due to the tumblehome design of the hull). In order to best facilitate that, I think I want to glue the plastic deck to the bow, let it dry, and then smooth out the join seam, and paint it the hull black color. THEN, I would attach the wood over the plastic deck, carefully minding the edges up on the bow, and after that was in place, then I would add the tumblehome sides to the plastic deck with the wood laminate, and have the deck fit right into those slots on the inside of the hull.
I think it will be easier to do than to describe here, so I'll just be sure to show lots of pictures as I do that step. More to follow!
The kit has porthole rings molded in already. But the thought of painting them all brass is a nightmare. So I drilled them all out, and scraped off all the molded-in rings to give me a flat hull to glue the rings to.
What the WEM rings do is they allow you to put a perfectly shaped brass ring around your portholes. And, you can paint right up to them, around them, and even over them. THEN, when it's all dry, you can take an X-Acto blade or sandpaper and carefully scrape any paint off of the face of the ring, exposing the shiny brass underneath.
Presto! Black hull, polished brass porthole ring - perfectly round, perfectly edged, perfectly uniform thickness. Perfect.
My son and I spent some time perfecting a technique to mount all of these buggers, and we came up with a pretty good four-hands approach that I thought I would share here.
First, we cut the rings from the brass sheet and placed them on a brass rod. Tape on the rod keeps them from falling off the back, and also provides a pretty workable grip. By placing the rings on the rod as a block, you also have a large consistent surface that you can file as a group to remove the burrs from where you cut the rings from the sheet to help ensure good roundness. Any burr will stick up and thus be easy to identify and file down.
Next, a single ring is isolated and slid down the rod with a blade or fine tweezers: With the ring ready to go and in my son's able hands, I would place a drop of CA glue over the drilled hole, forming a ring around the outside. My son would insert the rod in the hole, slide the ring the rest of the way down into the glue, and press it into place with some sharp tweezers (the ones with the bent head proved to be highly effective here!) He would then extract the rod from the hole, holding the ring in place with the tweezers. Most of the time, but not all of the time, the ring will stay where it is supposed to stay when the tweezers are withdrawn. If so, then I would squeeze the ring firmly into place, clamping it between my thumb and forefinger with a paper towel to soak up any excess glue. I would then prep the next hole by scraping as appropriate, and preparing to add my drop of glue.
Meanwhile, my son would carefully sand any lingering glue from the tip of the rod, and also the tips of the tweezers if needed. We sanded the rod after just about every porthole, and sanded the tweezers after every few. You'd develop your own rhythm for that - once the rings start sticking to the rod, or coming away with the tweezers, it's time for tool cleanup! In terms of progress on the Borodino, we have over half of the portholes in place now after a few hours of four-hands work. I hope to get the rest of them in place tonight, so then I can paint and scrape the brass. Once those are in place, then the the hull prep is just about wrapped, and I can FINALLY glue down my aft deck, and I'll be able to post some pictures of that in place.
As for the fore deck, it's really tricky. It attaches to the bow directly, but also sandwiches between the huill sides in a slot in the middle of those pieces (this is all due to the tumblehome design of the hull). In order to best facilitate that, I think I want to glue the plastic deck to the bow, let it dry, and then smooth out the join seam, and paint it the hull black color. THEN, I would attach the wood over the plastic deck, carefully minding the edges up on the bow, and after that was in place, then I would add the tumblehome sides to the plastic deck with the wood laminate, and have the deck fit right into those slots on the inside of the hull.
I think it will be easier to do than to describe here, so I'll just be sure to show lots of pictures as I do that step. More to follow!
scaledecks.com - Proud Sponsor of the ModelWarships.com community!