The Ship Model Forum

by **Winks** » Wed Jun 08, 2005 1:06 am

White Ensign Models enamels. Available direct (England) or, in the US, from Pacific Hobbies.

by **atago46** » Tue Jun 07, 2005 8:09 am

Hey winks
what brand is WEM enamals.
I have always used MM, but I would like to give
another brand a try. Like maybe that WEM your talking about..
Robert.....
Glassboro,NJ 08028

by **Tony Bunch** » Mon Jun 06, 2005 8:38 pm

Hi Timmy,
What I previosly wrote is ALL that I ever have done, so I suppose the answer is....no.
Clean after each use, that's the key.
Tony

by **Timmy C** » Mon Jun 06, 2005 5:03 pm

But how do you clean the inside of the nozzle? Wouldn't the paint all dry up inside? Thanks.

by **Tony Bunch** » Mon Jun 06, 2005 1:07 am

Hi Timmy,
I assume that you are referring to the airbrush cleaning process.
With the B-150il, I only remove the needle and wipe it clean. While the needle is removed, the head is cleaned with a toothbrush soaked with whatever solvent is being used.
This is usually all that is required to keep the 150il clean.
This process must be done after EVERY use, no matter how small the task.
hope to be helpful, Tony

by **Timmy C** » Sun Jun 05, 2005 7:18 pm

Tony: Any tips on how to cover the tip of the nozzel for the back flushing? Since it's in that weird tri-point shape, it's hard to cover it completely.

by **Winks** » Sun Jun 05, 2005 5:01 pm

Oh yeah... I hate yellow. It causes me no end of grief.

And, I have come full circle back to enamels. I recently tried the WEM enamels - it was like I done died and gone to heaven. Smooth and easy and thin and even. I always seemed to have trouble somewhere along the line with acrylics. No more. I had come to the conclusion that I would never, never use MM acrylics no matter what. Now, it is likely I won't use acrylics at all for spraying. Other than drying time and doing it in the garage for the fumes, enamels seem to have little downside.

by **Tony Bunch** » Sun Jun 05, 2005 4:34 pm

Hi Guys,
Timmy,
Badger 150il. Double action, cleans easily and works good. The Co2 cylinder is now 3 years old, and I have had it refilled 4 times.
Would'nt do it any other way!
take care, Tony

by **Timmy C** » Sun Jun 05, 2005 2:09 pm

Lol. Is that the Badger 150? I've got the same one. Haven't tried it yet though.

by **Tony Bunch** » Sun Jun 05, 2005 1:20 pm

Hi Guys,
Timmy:
Do try this at home!

Simplicity, and great results!

remember Timmy: if I didn't care, I would not bother

BTW: painting very small parts, (especially white), is made much easier using an airbrush...even if multiple coats are needed........
faithfully submitted, Tony Bunch

by **Vlad** » Sun Jun 05, 2005 4:27 am

I have trouble with two.

WEM AP507A admiralty dark gray
WEM Kriegsmarine dark gray.

not sure why, but they cover a lot worse than everything else in their CC range.

by **Timmy C** » Sat Jun 04, 2005 9:09 pm

Tony: Only time whites are used are on those small little radar domes. Too small to justify setting up and cleaning the airbrush.

by **Tony Bunch** » Sat Jun 04, 2005 8:54 pm

Hi modelman62,
In what way are you having problems. What do you mean, 'doesn't seem to do right"?
You are spraying; I figured that much.
Is the airbrush clean?
Are you using compatible paints/thinners?
Is the surface clean?
Is the paint mixed for airbrush use to the consistancy of milk?
Pressures around 20 psi.
Was it exceptionally moist outside?
Do you have a compressor or a Co2 cylinder?
If a compressor, do you have a water trap?
Are the base colors the same, if so maybe consider primer grey, (airbrushed on), first.
Is there adequate light.......big concern?
faithfully submitted, Tony Bunch
ps Timmy: time for an airbrush, my boy!
BB, CB and DDG Fan!

by **Timmy C** » Sat Jun 04, 2005 6:57 pm

Gloss white. Impossible to handpaint while looking good.

by **Guest** » Sat Jun 04, 2005 6:18 pm

YES YOU ARE NOT ALONE!!!

here are the colors i have absoulutely no luck with

Tamiya-All gloss colors and flat white& metallics
ModelM- Yellow

by **modelman62** » Sat Jun 04, 2005 4:12 pm

.... and find them worse than others? LIke this MM enamel Flat sea blue im doing, just doesnt seem to do right.

Maybe cause its so dark or something. I was just wondering if anyone else had the same thing happen with certain colors.

The Ship Model Forum

Does anyone have trouble spraying a certain color....

Post a reply

Expand view Topic review: Does anyone have trouble spraying a certain color....

WEM Enamels

WEM Enamals

yo Timmy!

cleaning

Problem colors

Hi Timmy

This is for Timmy!

paint problems?

Does anyone have trouble spraying a certain color....